GAIN up to 35HP with no other changes.

$319.99

Ford 4.6/5.4 DOHC 1993-2004 (2/set). These gaskets have an expanded steel core that provides stability and maximum torque retention to eliminate gasket failure. The graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. The gaskets conform to and seal minor surface irregularities, high recovery material allows header or manifold flange to stay sealed if flange loses correct clamp-load. They can be trimmed if necessary for modified port applications. Used for OE replacement, high performance street, drag race

This spacer better distributes airflow to the engine by raising the upper intake hat and increasing volume, Pick up 10-12 HP! Forced induction applications run safer and more powerfull to better airflow distributiuon. Includes gasket and new Hardware.

This kit includes Super High Quality black oxide coated Allen Head re-usable bolts that hold the intake manifold to the cylinder head, works with all factory and aftermarket DOHC manifolds.

DOHC (99-04 only)

This kit includes 10  3" long wheel studs. Studs can be tapped in or pressed in. NHRA REQUIRED for all vehicles running drag wheels or tires (2 packs required for front and rear)

QTY 10

This complete kit allows you to vent the valve cover/crank case pressure to the atmosphere, This prevents your turbocharger or supercharger inlet tube from sucking oil out of the engine and burning it which causes smoking, oil leaks, and poor performance. Kit includes all lines and fittings to attach to factory valve cover. Breather tank includes filter and mounting bracket and can be mounted in any location including the fenderwell.

SALE

$199.99

These 100% Billet CNC Machined Coil Covers are CNC engraved with either Supercharged or Turbo charged writing and are a direct fit on ALL 99-04 DOHC engines (including Navigator). Includes new Allen Head hardware.

32v

TurboCharged

100801B

32v

Supercharged

$119.99pr

These new fully assembled heads feature MMR stage 1 intake & Exhaust porting and polishing, fully assembled with new factory valves and springs. Gain 20-30 HP over a non ported 03/04 Cobra Head

Options include free install

MMR stainless steel High flow valves $379.99

Comp High performance/High Lift springs (compatible w/ all cams) $349.99

Titanium Valve Retainers $449.99

2003-2004 Cobra Cams + $200

Comp cams Billet stage 1-3 + $1099.99

These new fully assembled heads feature MMR stage 2 Intake,Exhaust and combustion chamber porting and polishing, fully assembled with new factory valves and springs. Gain 45-55 HP over a non ported 03/04 Cobra Head

Upgrades ( includes free install)

MMR stainless steel High flow valves $379.99

Comp High performance/High Lift springs (compatible w/ all cams) $349.99

Titanium Valve Retainers $449.99

2003-2004 Cobra Cams + $200

Comp cams Billet stage 1-3 + $1099.99

Includes 03/04 Cobra Cams, lifters and followers not included

Gain up to 20 HP on N/A engines or up to 35 on S/C or Turbo applications! Direct bolt on.

FREE SHIPPING

Great performance gains and Comp cams go hand in hand, stage 1 cams can use factory springs, stage 2 and 3 require High lift springs. Stage 1 Cams great forN/A or Nitrous cars with Bolt ons, stage 2 and 3 great for engines with head work, increased compression, stroker engines etc. Call for your application. Custom N/A cams also available.

Great performance gains and Comp cams go hand in hand, stage 1 cams can use factory springs, stage 2 and 3 require High lift springs. Stage 1 Cams great for Forced Induction(supercharged, Turbo Charged) cars with Bolt ons, stage 2 and 3 great for engines with head work, stroker engines, increased boost, turbo Chargers etc. etc. Call for your application. Custom cams also available.

101731-100733

This is a great cam kit for N/A, S/C or Turbo Motors, we have seen gains as high as 45HP. Turbo applications should use MMR custom turbo cams below. Kit includes new stainless steel swirl polished valves, special roller lifters, new camshafts (not regrinds), and new valve stem seals. 254/258 and 12mm Lift (roughly .500) Also great for assembling bare FR 500 heads.

MMR 96-04 GT/Cobra/Bullitt/ High performance Factory Airbox replacement kit
Gain up to 11 HP!! Replaces entire factory airbox with high flow washable filter and CNC machined billet aluminum mass air flow adapter.

Call to order

Fits all Aviator DOHC manifolds, these rails can support up to 1200 HP, includes all hardware and brackets, blue anodized.

Fits all 99-01 Cobra and Mach one, includes MMR fuel pressure sensor adapter, red anodized, supports up to 1400 HP. For use with return or non return systems.

The Baddest head ever available from Ford, factory equipment on Ford GT supercar, Requires custom intake manifold available through MMR Part#100735. These heads are fully assembled with high lift springs, Stainless Intake Valves and Inconel Exhaust valves, cams, lifters and rockers not included

Recommended for all Forced induction applications and aftermarket camshafts, compatible with all factory locks and retainers

96-98 Accufab Billet Oval Throttle Body
This single blade High flow Throttle Body is great bolt on can gain up to 15 HP on a stock 96-98 Cobra, and up to 30 HP on forced induction applications!!

FREE SHIPPING